☀️ Lock In Lock Out Procedure

1. Engineering manager, FM managers and supervisors should annually verify that all associates are in compliance with the requirements of this procedure. A periodic lockout/tagout inspection form shall be used and a copy of the completed form sent to the FM safety manager. 2. Use this guide to develop an effective lockout-tagout process for your worksite. 1. Shutdown preparation. Everyone occupying the worksite should be trained on proper LOTO procedures as well as the potential hazards present within the space. Educating employees is the first step to a successful repair job. 2. Notify employees. A lock out tag out refers to the procedure and practice of disconnecting and isolating equipment and machinery to prevent the release of hazardous energy or the unexpected re-energisation of that machine or equipment. Lock out tag outs (also commonly written down as LOTO) are performed by companies across a number of industries, including Authorized employee – An employee who performs servicing or maintenance on machines and equipment. Lockout or tagout is used by these employees for their own protection. Definitions. Affected employee – An employee who performs the duties of his or her job in an area in which the energy control procedure is implemented and servicing or the lockout, then the lockout is complex and the general lockout procedure may not be used. A complex lockout procedure is required. 8. Authorized worker . Relieves, exhausts, or restrains stored or residual energy in the machine or equipment by grounding, blocking, bleeding down, et cetera . 9. Authorized worker Verifies zero energy by The Canadian Centre for Occupational Health and Safety (CCOHS) in Hamilton, Ontario lists the following basic steps in a standard lockout/ tagout procedure: • Identify the energy source (s) that must be locked; • Notify all relevant employees of what is being locked, why, for how long and who the authorized individual conducting the lockout is; The basics of lockout/tagout for crane workers. Lockout/tagout policies and procedures protect workers from hazardous energy during overhead crane repair and other machine and equipment service. Chris Brewer, Technical Trainer. The intention of lockout/tagout is to lockout and dissipate all energy sources—and verify a zero-energy state Lockout/Tagout Procedure (4) Shut down the air handler supply/return fans by calling the HVAC BMS Department who will shut down the control signal to the unit. (5) Deactivate the electrical energy by turning off the power at the VFD disconnect for each unit. (6) Lockout the disconnect for each VFD with shop or individually assigned locks. A Lockout permit form [DOC – 71 KB], [PDF – 85 KB] should be used in conjunction with the Lockout procedure and diagram provided above. The use of lock boxes for key control is recognized as a best practice. Make sure that only one key exists for each assigned lock and that only the affected employee has the key. Lockout/Tagout guideline. • Become familiar with these guidelines. • Be properly training in the use and implementation of the Lockout/Tagout Guidelines before utilizing them in the field. • Always follow these guidelines and use approved devices when performing maintenance tasks. • Maintain personal lockout/tagout supplies. LOTO i.e. lockout tagout safety procedure include six steps which are listed below. let us move to the steps of loto and learn each steps in detiails. Preparation of shutdown. Shutdown of the equipment. Isolation of energy. Lockout/tagout. Stored energy check. Isolation verification and de-energization of the machine. Procedures - Review your appraisal to begin to develop equipment specific procedures; you can identify lock out tagout product requirements during this phase also. Procedures should then be posted Lock-Out, Tag-Out, and Try-Out Pay particular attention to the last step in locking out equipment – verify that the residual and stored energy has been released. Remember – Lock Out, Tag Out, and then Try Out. Make sure that you’re not surprised by residual energy, as happened in this case: Figure 3 lockout/tagout. Topics include types of energy sources, the energy control plan, situations requiring lockout/tagout, lockout/tagout devices, energy control procedures and special lockout situations. PROGRAM OUTLINE TYPES OF ENERGY SOURCES • In order to control energy correctly, we must first understand the types of energy sources we may find 1. LOTO Procedure . LOCKOUT TAGOUT PROCEDURE . Equipment Identification. Equipment Name/Description: Band Saw (HH Roberts) Equipment Location: .

lock in lock out procedure